成都防腐风机厂家-生产销售玻璃钢风机,不锈钢风机,防腐风机,塑料风机等
全国咨询热线: 18981777134

成都高压不锈钢风机

9-19型高压离心式通风机一般用于锻冶炉及高压强制通风机,可广泛用于输送物料,输送空气及无腐蚀性不自然,不含粘性物质及气体。介质温度一般不超过50℃(更高不超过80℃)。介质中所含尘土及颗粒不大于150mg/m3


特殊定制:

产品属性:

生产周期:

服务承诺:《品质保证 按时交货 一年保修 售后无忧》

产品咨询,订购电话: 18981777134
产品详情
  • 不锈钢9-19高压离心成都风机

     9-19型高压离心式通成都风机一般用于锻冶炉及高压强制通风机,可广泛用于输送物料,输送空气及无腐蚀性不自然,不含粘性物质及气体。介质温度一般不超过50℃(更高不超过80℃)。介质中所含尘土及颗粒不大于150mg/m3
    产品型式:本厂机号有NO3.15、3.55、4、4.5、5、5.6、6.3、7.1八种。可制成右旋和左旋两种型式,叶轮顺时针旋转,称为右旋风机。以“右”表示,叶轮逆时针旋转,称为左旋风机,以“左”表示。风机的出口位置,以机壳的出风角度表示,9-19型风机NO3.15~7.1出厂时均做成多种型式,可根据使用单位要求安装成所需的位置,即出成都风口位置调整范围0°~225°或45°,即(0°、45°、90°、135°、180°、225°)共六种。NO7.1根据用户需求制成一种方向角度。风机的传动方式为A式(NO3.15~6.3)和D式NO7.1两种。
    结构特点:本风机主要由叶轮、机壳、进成都风口、机架、底架、轴承箱等皮带传动而组成。叶轮:由10个后倾的机翼型叶片、曲线型前盘和平板后盘组成,并经过动平衡校正,气动性能,故运转平衡、振动小、效率高、寿命长等特点。机壳:用钢板焊成蜗型壳体。进风口:制成整体(全部模具成型),装于风机的侧面,于轴向平行的戴面为曲线形状,能使气体顺利进入叶轮,且损失较小。传动组:由主轴、轴承箱、联轴器等。主轴由优质钢制成,轴承箱整体结构,采用滚动轴承,分为水冷和油冷两种。

  • High pressure centrifugal fan

     9-19 high pressure centrifugal fan is generally usedforforging furnace and high pressure forced fan, can bewidely used in conveying materials, conveying air andnon-corrosive nature, non-sticky substances and gases. The medium temperature is generally not more than 50℃ with maximum below80℃. The concentration of mediacontaining dust and particles is not more than 150mg/m3.Product type: The factory number is NO3.15, 3.55, 4, 4.5, 5, 5.6, 6.3, 7.1. It can be made into two types: right-handed and left-handed. The impeller rotates clockwise and is called a right-handed fan. Expressed as "right", the impeller rotates counterclockwise, called the left-handed fan, and is represented by "left". The outlet position of the fan is expressed by the air outlet angle of the casing. The 9-19 type fan NO3.15~7.1 is made into various types when it leaves the factory. It can be installed to the required position according to the requirements of the unit, that is, the position of the air outlet is adjusted. The range is 0°~225° or 45°, that is, (0°, 45°, 90°, 135°, 180°, 225°). NO7.1 is made into a direction angle according to user requirements. The transmission mode of the fan is A type (NO3.15~6.3) and D type NO7.1.Structural features: The fan is mainly composed of impeller, casing, air inlet, frame, chassis, bearing box and other belt drives. Impeller: It consists of 10 backward-inclined airfoil blades, curved front plate and flat rear plate. It has dynamic balance correction and aerodynamic performance, so it has the characteristics of balanced operation, small vibration, high efficiency and long service life. Housing: welded with a steel plate into a volute casing. Air inlet: made into a whole (all mold molding), installed on the side of the fan, and the axially parallel wearing surface has a curved shape, which enables the gas to smoothly enter the impeller with less loss. Transmission group: from the main shaft, bearing housing, coupling and so on. The main shaft is made of high-quality steel. The overall structure of the bearing housing is made of rolling bearings and is divided into water-cooling and oil-cooling.

机 号
Model(NO)





转 速
Speed(r/min)
功 率
Power(KW)
机座号
Poles frame size-p
流 量
Volume(M3/h)
全 压
Total pressure(pa)
3.15A29000.75-2Y132S-2402-5452223-2262
29001.1-2Y80M-2617-8322231-2017
3.55A29001.5-2Y90S-2560-7602545-2590
29002.2-2Y90L-2860-11602554-2310
4A29002.2-2Y90L-2824-12643584-3597
29003.0-2Y100L-21410-17043507-3253
4.5A29004.0-2Y112M-21174-20624603-4447
29005.5-2Y132S-22281-25044297-4112
5A29007.5-2Y132S-21610-28445697-5517
290011.0-2Y160M-23166-34885323-5080
5.6A290011.0-2Y160M-22622-36197182-7109
290018.5-2Y160L-23996-49016954-6400
6.3A290018.5-2Y160L-23220-51539149-9055
290030.0-2Y200L-25690-69788857-8148
7.1D290037.0-2Y200L-24610-73761171-11596
290055.0-2Y250L-28144-998811340-10426


外形及安装尺寸示意图 Lnstallation size diagram



 gy1.jpg

标签:
在线客服
联系方式

热线电话

18981777134

上班时间

周一到周五

公司电话

18981777134

二维码
线